2ND PRINTING JAN ‘03MANUAL NO. 999-1668SEGA AMUSEMENTS USA, INC.www.seuservice.comOperators’s ManualUpright Version
2www.seuservice.com3www.seuservice.com For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester
2www.seuservice.com3www.seuservice.com2. PRECAUTIONS CONCERNING INSTALLATION LOCATIONThis product is an indoor game machine. Do not install it outsi
4www.seuservice.com5www.seuservice.comOPERATION AREAFIG. 2For transporting the machine into the location's building, the minimum necessa
4www.seuservice.com5www.seuservice.comApprox. 5 mmEnsure that all of the Adjusters are in contact with the floor.3. OPERATIONPRECAUTIONS TO BE HEEDED
6www.seuservice.com7www.seuservice.com Do not put any heavy item on this product. Placing any heavy item on the prod-uct can cause a falling down
6www.seuservice.com7www.seuservice.comTo avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visi
8www.seuservice.com9www.seuservice.com Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts da
8www.seuservice.com9www.seuservice.com4. ASSEMBLING AND INSTALLATION● Perform assembly work by following the procedure herein stated. Failing to c
10www.seuservice.com11www.seuservice.comINSTALLING THE GD-ROM DRIVE (SETTING GD-ROM DISC)POWER SUPPLY, AND EARTH CONNECTIONTURNING POWER ONWhen carryi
10www.seuservice.com11www.seuservice.comINSTALLING THE GD-ROM DRIVE (SETTING GD-ROM DISC)● Carefully handle the GD-ROM drive so as not to contaminat
VISIT OUR WEBSITE!
12www.seuservice.com13www.seuservice.com Remove the 1 truss head screw that xes the GD-ROM drive lid (DISC LID). And turn clockwise the lid to re
12www.seuservice.com13www.seuservice.com Insert both the GD cable connector (for data communication) and the power cord connector (JST NH6P) into
14www.seuservice.com15www.seuservice.com Attach the accessory stickers to both the Game Board and the Media Board. Insert the Key Chip straight
14www.seuservice.com15www.seuservice.comPOWER SUPPLY, AND EARTH CONNECTIONFIG. 6. 6 a AC unitMain SW offThe AC Unit is located on one side of Cabine
16www.seuservice.com17www.seuservice.comFIG. 6. 7TURNING POWER ONTurn on the AC unit's main switch to connect the power. When the power is connec
16www.seuservice.com17www.seuservice.comWhen the game machines of a same or similar type are installed side by side, their sensors may interfere with
18www.seuservice.com19www.seuservice.com5. PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE● Do not move the product with a GD-ROM disk inside. Rem
18www.seuservice.com19www.seuservice.comFIG. 8The following explanations apply to the case the product is functioning satisfactorily. Should there be
20www.seuservice.com21www.seuservice.comGAME OUTLINE Insert a coin and the credit indicator below the screen will count up. When enough coins have
20www.seuservice.com21www.seuservice.com Players can defend themselves against knives, oil drums and barrels thrown by enemies by shooting them. S
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:To maintain the safety:To ensure the safe usage of the product, be sure to read the following
22www.seuservice.com23www.seuservice.comITEMS A player can join a game in progress at any time by inserting coins and pressing the start button. In
22www.seuservice.com23www.seuservice.comPLAY HINTS Aim for the head! On any stage, the weak point of enemy characters other than the boss is the
24www.seuservice.com25www.seuservice.com7. EXPLANATION OF TEST AND DATA DISPLAYBy operating the switch unit, periodically perform the tests and data
24www.seuservice.com25www.seuservice.comFIG. 9. 1 bCOIN METERFIG. 9. 1 a SWITCH UNIT7-1 SWITCH UNIT AND COIN METERNever touch places other than those
26www.seuservice.com27www.seuservice.com7-2 SYSTEM TEST MODE Any settings that are changed by users during TEST MODE are saved upon exiting TEST MO
26www.seuservice.com27www.seuservice.comB. MEDIA BOARD TESTPowering off the system during the MEDIA BOARD TEST with a DIMM BOARD will erase the game p
28www.seuservice.com29www.seuservice.comC. SYSTEM INFORMATIONUse SYSTEM INFORMATION to check version and other information for system programmes.Scree
28www.seuservice.com29www.seuservice.comJVS TEST is used to verify the specs of the I/O BOARD connected to the Chihiro and to run input tests.I/O BOAR
30www.seuservice.com31www.seuservice.com JVS TEST INPUT TEST NODE 1/1 SYSTEM 00 PLAYER 1 0000 P
30www.seuservice.com31www.seuservice.comE. SOUND TESTUse SOUND TEST to test sound output and to select the stereo/mono/surround setting. Use the SE
Specication changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed.The parts of the product include warning l
32www.seuservice.com33www.seuservice.comF. C.R.T. TESTUse the C.R.T. TEST to adjust monitor colours and verify screen size.COLOUR CHECK Screen Moni
32www.seuservice.com33www.seuservice.comG. COIN ASSIGNMENTSUse COIN ASSIGNMENTS to set the credit rate for each coin inserted. Use the SERVICE Butt
34www.seuservice.com35www.seuservice.com(C) COIN TO CREDIT RATE Set the CREDIT RATE for each coin inserted. The "x COIN(S)
34www.seuservice.com35www.seuservice.com(H) GAME COST SETTING Use this mode to set the number of credits required to start a game.
36www.seuservice.com37www.seuservice.comH. CLOCK SETTINGUse CLOCK SETTING to set the Chihiro internal clock. Use the SERVICE Button to move the cur
36www.seuservice.com37www.seuservice.comI. NETWORK SETTING (CORE) Use the SERVICE Button to move the cursor to the desired test item. (When set
38www.seuservice.com39www.seuservice.comJ. NETWORK SETTING (MEDIA)Use NETWORK SETTING to establish and test network connections.This is only displayed
38www.seuservice.com39www.seuservice.com(B) SET IP ADDRESS This sets up the details of the communication network. Depending on the NETWOR
40www.seuservice.com41www.seuservice.comETHER+MOBILE Settings Use the SERVICE Button to move the cursor to the desired test item. (When settin
40www.seuservice.com41www.seuservice.comTo clear data, use the SERVICE Button to move the cursor to YES (CLEAR) and press the TEST Button. When the da
TABLE OF CONTENTSBEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:TABLE OF CONTENTSINTRODUCTION OF THE OWNER’S MANUAL1. HANDLING PRECAUTIONS
42www.seuservice.com43www.seuservice.com7-3 GAME TEST MODE GAME TEST MENU INPUT TEST OUTPUT TEST GAME ASSIGNMENTS GUN SETTING BOOKKEE
42www.seuservice.com43www.seuservice.com INPUT TEST PLAYER1 PLAYER2 START OFF OFF TRIGGER
44www.seuservice.com45www.seuservice.com OUTPUT TEST START1 LAMP OFF START2 LAMP OFF-> EXIT SELECT WITH SERVICE BU
44www.seuservice.com45www.seuservice.comPerform the following settings for each item. GAME DIFFICULTY: Set the level of difcult
46www.seuservice.com47www.seuservice.com GUN SETTING GUN MARK CHECK PLAYER1 GUN ADJUSTMENT PLAYER1 GUN DEFAULT ADJUSTMENT PLAYER2 GUN
46www.seuservice.com47www.seuservice.comPointing the gun at the screen displays the gun cross (sight) for that gun. You can check to see if the sight
48www.seuservice.com49www.seuservice.com PLAYER1 GUN ADJUSTMENT ←PLEASE SHOOT GRID WITH PLAYER1 GUN PRESS TEST BUTTON TO EXIT P
48www.seuservice.com49www.seuservice.com PLAYER1 GUN ADJUSTMENT↑PLEASE SHOOT GRID WITH PLAYER1 GUN PRESS TEST BUTTON TO EXIT PLAYER1 GUN ADJ
50www.seuservice.com51www.seuservice.com PLAYER1 GUN MARK CHECKING+OUT OF SCREEN 1P+ TEST OR START1 : TO MEMORIZE SERVICE O
50www.seuservice.com51www.seuservice.com PLAYER1 GUN DEFAULT ADJUSTMENTTEST OR START1 : TO SET DEFAULTSERVICE OR START2 : TO CANCEL PLAYER1 GUN D
SPECIFICATIONSINTRODUCTION OF THE OWNERS MANUALThis Owner's Manual is intended to provide detaile
52www.seuservice.com53www.seuservice.com BOOKKEEPING PAGE1/3 COIN 1 0 COIN 2 0 TOTAL COINS
52www.seuservice.com53www.seuservice.com BOOKKEEPING PAGE2/3NUMBER OF GAMES 0TOTAL TIME 0D 0H 0M 0 SPLAY TIME
54www.seuservice.com55www.seuservice.comf. BACKUP DATA CLEARSelect BACKUP DATA CLEAR to clear the contents of BOOKKEEPING and Score Data.BACKUP DATA C
54www.seuservice.com55www.seuservice.comIn the cases where the gun's operation is not satisfactory or the gun sight deviates from the direction i
56www.seuservice.com57www.seuservice.comFIG. 10 aSCREW (11), black M3×16, w/flat & spring washersSCREW (1), blackM3×16, w/flat & spring washer
56www.seuservice.com57www.seuservice.comFIG. 10 b SLIDE MACHANISMFIG. 10 c Follow rst 3 steps of "Replacing the Microswitch." Remove th
58www.seuservice.com59www.seuservice.com Primary side and Secondary side The monitor's circuit which is divided into the Primary side and
58www.seuservice.com59www.seuservice.comFor the purpose of static prevention, special coating is applied to the CRT face of this product. To protect
60www.seuservice.com61www.seuservice.comSANWA Monitor: 998-0162 (31K Mode)CONTRAST BRIGHT H SIZE H POSI V S
60www.seuservice.com61www.seuservice.comFIG. 12 bCRADLE10. COIN SELECTORThe coin selector should be cleaned once every 3 months. When cleaning, foll
DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMANNon-technical personnel who do not have technical knowledge and expertise should refrain from per
62www.seuservice.com63www.seuservice.comDK5LCGHMEA241829JFB512817251427211922122016231311324C REJECT CUP SIDE PLATE891-1105-01292827262524M24L24K24J24
62www.seuservice.com63www.seuservice.com COIN DOOR
64www.seuservice.com65www.seuservice.com11. DESIGN RELATED PARTS1156789104321 ITEM NO. PART NO. DESCRIPTION
64www.seuservice.com65www.seuservice.com 1 CONTROL UNIT (HDT-2100)
66www.seuservice.com67www.seuservice.com 1 CONTROL UNIT (HDT-2100)
66www.seuservice.com67www.seuservice.com ITEM NO. PART NO. DESCRIPTION
68www.seuservice.com69www.seuservice.com ITEM NO. PART NO. DESCRIPTION
68www.seuservice.com69www.seuservice.com4 321 3 OTHER PARTS
70www.seuservice.com13. WIRE COLOR CODE TABLETHE WIRE COLOR CODE is as follow: A PINK B SKY BLUE C BROWN
WarrantyYour new Sega Product is covered for a period of 90 days from the date of shipment. This certies that the Printed Circuit Boards, Power Supp
This page left Blank
SEGA AMUSEMENTS USA, INC.
1www.seuservice.com1. HANDLING PRECAUTIONSWhen installing or inspecting the machine, be very careful of the following points and pay attention to ens
Comments to this Manuals